Replace the engine oil filter
Already dueWas expected around 50 h
Servicing the R32
- Brand
- Rippa
- Machine type
- Mini excavator 3–6 t
- Engine
- Kubota V1505
27Compatible attachments
89Listed parts
No manufacturer schedule for this model: here is the one for its machine type.
At 100 h on the meter, across 26 tracked service points.
Where you stand
- 50 h1 point
- 100 h8 points
- 100 hYou are here
Plus 6 actions to repeat at every use.
- Grease the boom and arm pins — every 8 h
- Grease the bucket pins — every 8 h
- Grease the blade pins — every 8 h
- Check the engine oil level — every 10 h
- Check the hydraulic oil level — every 10 h
- Check the coolant level — every 10 h
Already due 4
Kubota keeps this interval. prescribes 250 h for this engine — we keep the shorter one.
Grease the boom and arm pins
Already dueWas expected around 96 h
Where and how (6 points)
Where
- Boom foot pincentreWhere the boom hinges on the upper structure
- Boom cylinder base pincentreCylinder body side, on the upper structure
- Boom cylinder rod pincentreRod side, on the boom
- Boom-to-arm pincentreThe elbow between boom and arm
- Arm cylinder base pincentreOn top of the boom
- Arm cylinder rod pincentreOn the arm
How
- Lower the attachment to the ground, stop the engine and remove the key.
- Wipe each nipple before fitting the gun: otherwise you inject the grit along with the grease.
- Pump until a small bead of clean grease appears at the joint.
- Wipe off the excess: grease left proud collects grit and does the opposite of what you want.
Grease the bucket pins
Already dueWas expected around 96 h
Where and how (4 points)
Where
- Bucket pivot pincentreWhere the bucket meets the arm
- Bucket cylinder base pincentreOn the arm
- Bucket cylinder rod pincentreLinkage side
- Bucket linkage pinscentreThe two links between cylinder and bucket
How
- Rest the bucket flat on the ground, stop the engine and remove the key.
- Wipe each nipple before fitting the gun.
- Pump until clean grease appears, then wipe off the excess.
Grease the blade pins
Already dueWas expected around 96 h
Where and how (4 points)
Where
- Blade arm pin — leftleftOn the frame, left-hand side
- Blade arm pin — rightrightOn the frame, right-hand side
- Blade cylinder base pincentreUnder the frame, at the front
- Blade cylinder rod pincentreOn the blade itself
How
- Lower the blade to the ground, stop the engine and remove the key. Never work under a raised blade.
- Wipe each nipple, pump until a bead appears, wipe off the excess.
Due now 11
Check the engine oil level
Due nowDue now — at 100 h
Check the hydraulic oil level
Due nowDue now — at 100 h
Check the coolant level
Due nowDue now — at 100 h
Grease the slew ring gear teeth
Due nowDue now — at 100 h
Where and how (1 point)
Where
- Slew ring gear grease nippleundersideReached under the upper structure, arrow-marked
How
- Machine on level ground, attachment down, engine off.
- Find the arrow-marked nipple and wipe it clean.
- Inject about 50 g of grease — roughly twenty strokes of the gun.
- Slew a quarter turn and repeat: four injections cover the whole gear ring.
Grease the slew bearing race
Due nowDue now — at 100 h
Where and how (1 point)
Where
- Slew bearing race nippleundersideOn the bearing race
How
- Machine on level ground, attachment down, engine off.
- Pump slowly until you feel resistance, without forcing: excess pressure damages the bearing seals.
Check the battery electrolyte
Due nowDue now — at 100 h
Drain water from the fuel system
Due nowDue now — at 100 h
Check the track tension
Due nowDue now — at 100 h
Check the hydraulic hoses
Due nowDue now — at 100 h
Check and adjust the fan belt
Due nowDue now — at 100 h
Kubota keeps this interval. prescribes 200 h for this engine — we keep the shorter one.
Clean the air filter
Due nowDue now — at 100 h
Kubota keeps this interval. prescribes 200 h for this engine — we keep the shorter one.
Calendar-based
- Replace the radiator hoses every 24 months
- Replace the coolant every 24 months
Indicative information only. The manufacturer's manual is what counts.
A year of servicing
34 scheduled jobs
Plus 6 actions to repeat at every use.
Products to keep in stock
- Graisse NLGI 2
- ISO VG 46 (HV)
- SAE 90 (API GL-4)
We put no price on this: the reference knows the products, not the quantities. Price them yourself with your own supplier.
Reviews
Nobody has written here yet.
Write a reviewEvery review is read by a person before it goes live.